Hi Fernando. I was able to get the test code that you gave me for PFC8575 to work now I just need to assiggn the pins, I had seen in an other post here you showed how to assign the pins I just remember witch one. Can you repost for me. -------------------------------- Last edited Mon Dec 22, 2014 6:...

okay will try.


All work accept the ones that say 5volt GND and Vin.

Hi Fernando,

I tried the code change for db25 and was not able to get it to work, one question is does the pin configuration stay the same as in you previous post or do all pins become high low switched?

The ULN chip is all redy on the board or do I have to set up? Ip issue: I will check the sd card when I get home, serial said it was reading ok but that may not be the case? How hard would it be to add more buttons to menu 2 for service of pumps to turn off, on and automatic. As far as pump controls...

Can you post a link for ldd board I need one for 5 channels and fan as well.

-------------------------------- Last edited Thu Dec 18, 2014 1:02 am --------------------------------

Can you post a link for ldd board I need one for 5 channels and fan as well.

Ok so new issue was working on some other stuff and now no more Internet connection, when I bring up the serial monitor it give a server ip of 198.128.0.128 whitch is not the server I have it set up for I tried to reboot router and network, then I tried to change port on all three ferduino, router a...

Sorry willy the program won't what I thought, I have to do one tab at a time :| -------------------------------- Last edited Thu Dec 18, 2014 12:08 am -------------------------------- Sorry willy the program won't what I thought, I have to do one tab at a time :| -------------------------------- Las...

I found program that will translate all the comments without missing with the code one done would you like I can send it back and you can use as english.

ok I see all are named in ferduino tab thank you fernando.

Yes I did those steps and now I need to where to put name for each pin for what it controls, like use pin 1 for heater , pin 2 for chiller ...... These for the most part are to the relay board, except the pi for chiller is going to need to be different as chiller has it's own relay built in, I am go...

Hi Fernando which tab do I add code for control of pins from PCF8575?

I have figured out what happend on my network, it was something I forgot to change #-o . Next part will be to set up 16 relay board 120 volt items and controls as well as codde for PCF. :D -------------------------------- Last edited Tue Dec 16, 2014 1:11 am -------------------------------- I have f...

So new weird issue ferduino board working and online now, thank you so very much for the help Fernando, I have a new issue the ferduino kicked all most all other items off my home network but i will figure that one out. -------------------------------- Last edited Mon Dec 15, 2014 9:00 pm ----------...

So at this point I am not working on web control any more, I need to get this controller on my tank and running. I took all the files off my pc loaded only the ones that I needed for ferduino english and web control and still couldn't get to show on my network, I tried all test codes, all types of c...

Ok will try to correct when I get home from work. Thank you for your response.

-------------------------------- Last edited Sat Dec 13, 2014 6:03 am --------------------------------

Ok will try to correct when I get home from work. Thank you for your response.

Hi Fernando, Yes I had to load all new, I messed something up when I first started, do I have to old and new or just the new? -------------------------------- Last edited Sat Dec 13, 2014 1:17 am -------------------------------- Hi Fernando, Yes I had to load all new, I messed something up when I fi...

Hi Fernando,
I am getting this error when I try to upload new joy reef code.

Go here: Image: http://screenshots.portforward.com/routers/Dlink/DIR-815/Advanced_Port_Forwarding.jpg In the first row: Name: Ferduino IP Address: (ip you set in ferduino code) Public port and private port: choose the port you set in Ferduino Mega code In joy-reef in ip address put the addres ...

Hi, the new relays that I just got have a thicker and wider trace than the others, I asked before I bought them. trace is 5.5mm wide and 2.5oz thick. thank you for the info and, could you post a link to the calculator you showed?

Hi! most ssr only have 2 amp load rating reeflow pump runs at 2-6 amps constant. same with 300 watt heaters. I am having no luck with joy-reef ferduino. even called ISP to ask for help.