Hi! If all doubts were answered please mark this topic as solved. Best regards.

Hi, So, how can I move (directly inside of the library if it is possible) the pin of the RTC? P.S. I'm also having some problems with the example code of the PCF8574 library; I can't compile it with the arduino IDE...

Connected the pins 50, 51, 52 to the TFT shield and it works now I need test the touch. Thanks

Hi Fernando'm following your tutorials to put ethernet but I am not able to make it work got me I have the connections as follows: vcc gnd, miso ... 50 mosi .... 51 rst ........ 53 sck ...... 52 continued after the settings ferduino How to install Ferduino with web monitoring step by step up to To...

yes must be 2 GB max that was alot of issue I had been having. I treied a 4 GB card and had IP issues.

Hello, Fernando If it has made in such a way, was easier. With denem tip I have not got it there if (ORP > setORPFILTEREIN) // -100mV ORP Filter { digitalWrite(nitratfilterPin,HIGH); } if(ORP < setORPFILTERAUS) // - 50mV { digitalWrite(nitratfilterPin,LOW);

Thank you very much for your help.

Solved thank you

Hi! This 2 items are compatible but, I can't see a good reason to buy the IC, it is very small to soldering. For PCF8575 you need of 2 ULN2803, if your relay board activated with LOW signal. It's very cheap is better buy already to don't lose time. Check here what's an ULN2003. Best regards.

Hello fernando, was my mistake, I had the setup: wire.begin() deleted that line and everything worked. thank you

Glad to hear!

Hi! You're right, the circuits are identical. I never had problem of reset while the dosing pump was working so, I haven't the 12 V connected on pin 9 to make the circuit more simples. Anyway you can connect it to prevent problem of reverse current. Best regards.

Hi! Welcome Norberto! This TFT isn't compatible with my code. Buy a TFT 400 x 240. Best regards.

Haha. Wicked man! I didn't see that part :)) I will probably solder to some place on back of LCD PCB for vibration transfer into LCD and use redundant SD card pins. Thank you Fernando :ymhug:

Solved Code: #define CAL_X 0x00430ED8UL #define CAL_Y 0x002A0EECUL #define CAL_S 0x000EF18FUL and then in the code file FERDUINO in file ProcessMyTouch change the code: Code: x=myTouch.getX (); y=myTouch.getY (); on Code: x = 399-myTouch.getX (); y = 239-myTouch.getY (); Thank you very much

You can connect the ICSP headers using a cable like this: And a wire between pin 10 (shield) and 53 (Arduino)

You already asked. :) You need make inverse operation for this instruction. Please mark this topic as solved.

Thx Fernando!

HI! thanks for the reply!

[quote=" Guy Hall » Yesterday 6:14 pm ":1tke8efk] I am only planning on using ph at the mo and salinity later so I was going to save 18 and 19 for salinity and not need a multiplexer then if that works. I won't be using the wavemaker function for now as I have a mp10 so I could use those...

Hi, I write an e-mail to ITead to show them the problem... The hardware setup for the Ferduino is with an ITDB02 MEGA shield v1.1 right? Best regards Simone Yes.

Doh! #-o Thank you

Hi! Glad to hear. Best regards.

Thank you, I will get it ordered. Cant wait to get all the parts together to make this controller. Inspiring work you have done, really amazing. I will start a project thread once I get the rest of the parts :D

Thanks Fernando.