Hi! Please, do not mix the subjects on topics. To Ferduino without web control no need any changes on TFT shield. Best regards.

Hi! No matter. You can use the normal mode (gnd + data + vcc) too. Check if you have problem of oxidation on sensor. Best regards.

Hi! You can use any free pin. Best regards.

In the tab Ferduino change: const byte ChipSelect_SD = 4; const byte SelectSlave_ETH = 53; To: const byte ChipSelect_SD = 53; const byte SelectSlave_ETH = 4;

Hi Fernando I cleaned up the code and found the right adjustment for delays, delays after the "open channel" must be 50 to not make any mistakes. Now the probes of PH and ORP is working perfectly with new stamps "EZO". Thank you Fernando. :-bd...

Hi! This way: const byte ozonizadorPin = 80; // Pino que liga o ozonizador const byte reatorPin = 81; // Pino que liga o CO2 do reator. And: const byte temporizador1 = 47; // P0 // Pino que liga o timer 1. const byte temporizador2 = 48; // P1 // Pino que liga o timer 2. looking the code...

Olá! Glad to hear! Best regards.

12 * 5 = 60 seconds. Only ask is very easy. Look the code and try learn. void checkTempC() { contador_temp ++; sensors.requestTemperatures(); // Chamada para todos os sensores. temperatura_agua_temp += (sensors.getTempC(sensor_agua)); // Lê temperatura da água...

worked out very well for me all the files are there just the last 6 could not be open Thank you for teaching me this

Thx again Fernando! :-bd

All is possible. I'll not make it for you. Try learn a bit. The problem with texts is to other topic.

Hi Fernando, I resolve this problem jet, only need a "}" in a part of teh code, If you want, I put it here to download for you or everyone. Best regards.

Thank you Fernando :-bd It's too easy for you !!!! I add in my code and I remove the timer I had programmed.

Hi! Glad to hear. Real graphs on Joy reef only in next version, we are working on this. Here an example. Best regards.

Hi! The solution to this problem is simple. In the tab Stamps after: Open_channel(ph1); Serial3.print(tempC); Serial3.print('\r'); delay(500); And: Open_channel(ph2); Serial3.print(tempC); Serial3.print('\r'); delay(500); Add: Serial3.print("r");...

Glad to hear!

thank you Fernando my fault

Hi! Yes, if you have sensors placed as shown, you need only connect the "solenoidePin" in a relay to control the pump. Best regards.

awesome, OK I added this to the ferduino tab at the very bottom as below 215, 210, 205, 200, 190, 185, 180, 175, //16 - 17 170, 165, 160, 160, 160, 150, 145, 140, //18 - 19 135, 130, 125, 115, 100, 75, 60, 30, //20 - 21 30, 30, 28, 28, 0, 0, 0, 0 //22 - 23 }; byte *cor[5] = {wled, bled,...

Hi! If the problem was solved please mark this topic as solved clicking on button " accept this answer " below of the post that helped you. Best regards.

Thanks for the info Len

Hi! Firstly, no put personal information here. Always use this tag to post a code. This is wrong. char *credencial = "jeremy:******"; I told to use ONLY numbers on password. You need configure the password on Joyreef also. Look this topic to see how test with local IP. Best regards.

Will do Fernando I also solved my RTC issue by using a IC2 scanner to find the IC2 address, it was very simple and easy. For anyone who needs it it can be found here The example shown is for a Tiny RTC DS1307 but it shoulld work for any IC2 device. Thanks again and now on to more testing! Regards...

Hi Fernando, Thanks for your answer, that was the solution. I think that something has changed it from arduino mega to arduino uno.I did not noticed that. Len