New build.

[Christopher Kindig]

Ok thank, you once again.

[Ruben Wijnhoven]

Just change the nivel code. What I did was build a float switch and put it on channel 6. Then alter the nivel code so it only monitors channel 6 plus i altered the low text to high. So now when my return pump fails it will trigger the float and the level text will change from normal to high. Plus i altered the code so it puts 25 at reactor ph when triggered and 0 when all is well. I then set the alert on joy reef for the ph reactor. So now when my return pump fails i get a warning form joy reaf my reactor ph is wrong. Quick and dirty solution but it gets the job done.

[Christopher Kindig]

Hi Fernando, I was working with the code this morning and had a JAVA error come up has any one else had this issue, the error reads.

[Christopher Kindig]

okay so after uninstall and reinstall problem IDE is fixed

[Christopher Kindig]

Hi Fernando I tried to run 12 volts on the board again and no luck am I doing some thing wrong, I have 12volt positive and ground at the power port and now nothing is working every thing comes on when power on and stays on.

[Christopher Kindig]

new pump temp setup.

so this my new pump after a failure of my 1. year old internal retun pump.

-------------------------------- Last edited Tue Feb 10, 2015 2:37 am --------------------------------

and also another full on sour note dont let a 12 volt line touch the back of the heat sink on the board, I was working with unit cleaning some stuff up and one my kiddos moved some wires to get some thing off my desk and zap, I was able to do as fernando suggested and remove all components and turn it into a shield but some things are not quite right so new board here I come

[Christopher Kindig]

Hi Fernando are EC and density going to be the same code in ferduino I just received my probe and would like to set it up, also is there a calibration code for EC or do I use atlas code? I did check in some topics and did not see any thing specific.

[Fernando Garcia]

Hi!

Why you need of EC and SG?

The code is ready to SG.

To calibration you need use the test code.

Best regards.

[Christopher Kindig]

Just wanted to make sure that there was nothing specific I had to do before using the ec probe, and it connects to number 3 stamp, correct?

-------------------------------- Last edited Thu Feb 12, 2015 4:29 am --------------------------------

Just wanted to make sure that there was nothing specific I had to do before using the ec probe, and it connects to number 3 stamp, correct?

-------------------------------- Last edited Thu Feb 12, 2015 4:30 am --------------------------------

Just wanted to make sure that there was nothing specific I had to do before using the ec probe, and it connects to number 3 stamp, correct?

[Fernando Garcia]

Yes, connector 3.

[Christopher Kindig]

Ok thank you, I will have to get a db 25 cable right now the brakeout board is in the way.

[Fernando Garcia]

You'll buy my relay board?
The cable isn't needed on this case because goes together.
I'll get the relay board in next week probably.

[Christopher Kindig]

I will still need a cable, relay board is going to be in a gang box with the out lets so there is no power interference between the to types of voltages. Do you have a price for the relay board yet?

-------------------------------- Last edited Thu Feb 12, 2015 4:59 am --------------------------------

I will still need a cable, relay board is going to be in a gang box with the out lets so there is no power interference between the to types of voltages.

[Fernando Garcia]

I'll have in the next week.

[Christopher Kindig]

I know why it double post , when I back out on my phone it re posts for some reason. EC stamp making things unstable
and I am looking forward to the relay board , do you have an eagle or gbr file of the board I am having a hard time to fallow the other schematic I am trying to find a common thing between all the issues from when the board was shorted, so fare I have the RX issue with Ethernet communication when EC stamp is plugged in it makes the board unstable and that's' it so far.

[Fernando Garcia]

Sorry, I can't give this files.

[Christopher Kindig]

I understand can you tell me is there one common link between these items.

[Fernando Garcia]

Only the GND because stamps are 5V and ethernet 3.3V.

[Christopher Kindig]

Ok, thank you for the reply.

[Fernando Garcia]

Hi!

The EC stamp works fine with test code?

Which type of instability do you have?

Best regards.