Problem with ethernet module [SOLVED]

[Sueur Aurelien]

Hi

I have a module ENC28J60, i have a led red is on and when i plug a RJ45, green led is on and orange led flashing.

I can PING ip address, but when i use ADVANCED IP SCANNER in local network, there is no port open (80)

How i can check it in the local network ?

[Fernando Garcia]

Hi!

What code you are trying use?

Best regards.

[Sueur Aurelien]

Code: Select all

boolean Ethernet_Shield = true; // Altere para "false" caso não tenha um Ethernet Shield conectado ao Arduino.

char *credencial = "aurel71:******"; // Coloque aqui seu usuário e senha cadastrados no www.joy-reef.com. Usuário e senha devem estar separados por dois pontos (:);
                                              // Use apena letras minúsculas.
                                             
byte maxima_tentativa = 3; // Número máximo de tentativas de autenticação.
unsigned long intervalo_tentativa = 15; // Tempo  de espera (em minutos) para novas tentativas.

byte mac[] = {0x00, 0x09, 0xB0, 0x43, 0x00, 0xFF }; // Este MAC deve ser único na sua rede local.
byte ip[] = {192,168,0,200}; // Configure o IP conforme a sua rede local.
IPAddress gateway(192,168,0,254); // Configure o "Gateway" conforme a sua rede local.
IPAddress subnet(255,255,255,0); // Configure a máscara de rede conforme a sua rede local.

EthernetServer server(80);// Coloque aqui o número da porta configurada no seu roteador para redirecionamento.
                          // O número da porta deverá ser obrigatóriamente um destes: 21, 25, 53, 80, 110, 143 ou 443.
                         
unsigned long intervalo = 0;
char *inParse[50];
boolean web_teste = false;
byte tentativa = 0;
boolean web_dosage = false;
unsigned long millis_dosagem = 0;
boolean web_calibracao = false;


-------------------------------- Last edited Thu Jun 12, 2014 5:39 am --------------------------------

I configure the router (NAT) and test with JOYREEF a connection error message.

I tested my router with another server, and it works.

I think the web service is not UP on the Ferduino ??

[Fernando Garcia]

Hi!

You tried with the example available here?

viewtopic.php?f=8&t=42


You did port forwarding on router?

Best regards.

[Sueur Aurelien]

Hi!

With the code test: on my web browser it work i see the time spent and http://ping.eu/port-chk/ say port 80 open

with the Ferduino code : on my browser don't work and http://ping.eu/port-chk/ say port 80 closed

i have same address ip with all code


Best regards

[Fernando Garcia]

Why you want access the Ferduino directly?

Do you have all configured, so open the joyreef to control the Ferduino.

[Sueur Aurelien]

Fernando Garcia » 5 minutes ago wrote:

Why you want access the Ferduino directly?

for check it at local lan

i can ping 192.168.0.177 So the module is up

[Fernando Garcia]

You can't control Ferduino with local IP, because haven't web pages stored on Arduino.

[Sueur Aurelien]

i think so module is up but server port 21 is not up !

[Fernando Garcia]

Hãã?

If you have the port 80 configured on code and router, why you want use the port 21 on Joyreef?

[Sueur Aurelien]

I have test with many port but always same in the code and in the Joyreef.
Just for information i am newbies for arduino code but i am à network technicien.
But this not resolve my problem.

Best regards

[Fernando Garcia]

I don't understand your problem.

First you talk about port 80, after about the port 21.


What message of error the Joyreef show for you?

[Sueur Aurelien]

Hi Fernando

On joy-reef I have "connection error"

I did a test with Ferduino on port 21 with my router fowarding on port 21 and the setting of joy-reef on port 21.

and I did the same thing with port 80 and it still does not work.

[Fernando Garcia]

Hi!

Open this website and encode your username and password to base 64.

http://www.base64encode.org/

Use this format: username:password.

Open your browser and put an URL as this:

http://192.168.0.200:21/?cmd=your_usern ... ase_64,0,k

Open the serial monitor to see if the arduino receive some request.

Best regards.

[Sueur Aurelien]

Fernando Garcia wrote:

http://192.168.0.200:21/?cmd=your_usern ... ase_64,0,k

Thank you it allows me to test locally and it works locally.

I tested my router with another web server and my port 80 was open.

My ip gateway is 192.168.0.254 I had changes in ferduino code but it did not work.

I gave ip 192.168.0.1 default gateway in Ferduino and I changed my router (gateway) to this address.

and everything works

thank you for your patience

Thank you again

[Fernando Garcia]

Glad to hear!